Putting a harness on a pug can be a challenge, but with the help of this article, it’ll be a breeze. By following the instructions in this article, you’ll be able to put on your Pug’s harness quickly and easily.

1. Start by fastening the harness around the Pug’s chest with the appropriate size and type of buckle.

2. Next, secure the leash to the front of the harness. Make sure that it’s tight enough so that your Pug cannot pull away from you, but not so tight that it causes discomfort or irritation.

3. Finally, hook the Pug’s collar around his neck and tighten it as needed.

How do you put a harness on a pug?

Putting a harness on a Pug can be tricky, but with a few simple steps, it can be done. Here are the steps:

1. Start by finding the correct size harness for your Pug. Measure your Pug’s chest around the widest part and purchase a harness that is at least 1 inch wider than that measurement.

2. Make sure that the harness is tight but comfortable for your Pug. You may need to adjust the straps once you have them fitted.

3. next, put the harness on your Pug in reverse order of how it would fit humans: back first, then chest, then legs. Straps should be tight against your Pug’s skin, but not too tight so as to cause discomfort or pain.

4. Finally, attach the leash to one of the loops on the front of the harness and attach the other end to a sturdy object such as a post or railing.

Remember: always use caution when walking your Pug with a harness and leash, and be sure to check the fit frequently to make sure it is still comfortable.

Why would you want to put a harness on a pug?

Putting a harness on a pug can be a great way to help them stay safe while out and about. Harnesses typically have attachment points that attach to the dog’s chest or neck, which helps keep them from moving around too much and getting injured. They are also typically fitted with bells or other devices that make them more visible to drivers and other passersby, which can help alert people if the dog is in danger.

Tips for Harness Training a Pug

When you’re training your pup to wear a harness, you want to make sure the process is done slowly and correctly so as not to overwhelm your dog. The following tips will help ensure the process goes smoothly:

1. Start by teaching your pup to sit and stay. Once your pup is sitting calmly beside you, attach the harness onto the front of his collar and fasten it snugly but not too tight. Make sure the straps are positioned so they don’t rub or contact his skin.

2. After your pup is comfortable with the harness, begin attaching it to a sturdy object, like a post or tree branch, using a leash or a makeshift harness clip. If you’re using a leash, make sure the loop is big enough for your pup to stand up in and doesn’t tighten too much around his neck (a loose fit will help him adjust to wearing the harness). Be patient – he may resist at first, but with time and patience, he’ll get used to wearing it.

3. Once he’s comfortable with the harness being attached to an object, it’s time for the next step: teaching him to walk quietly and confidently in the harness. Start by leading him around the house, holding the leash in one hand and gently tugging on the harness to keep him close. Once your pup is walking calmly beside you and following your commands, it’s time to take things a step further.

4. Experiment with different types of walks – short strolls around the block, long walks along a path and even hikes up a nearby hill. Be patient with your pup – he may not be used to wearing a harness yet and may take a little bit of time to get used to it. And remember: always reinforce good behavior with treats and praise!

Tips for walking your Pug with the harness on

Putting on a harness is a great way to keep your Pug safe while you are out walking. There are a few different ways to put the harness on your Pug, and each method has its own advantages and disadvantages. Here are three tips for putting the harness on your Pug:

1. Use the belt loop method: This is the easiest way to put the harness on your Pug. Just loop the belt around his neck, and tighten it so it is snug but not too tight.

2. Use the slip-over method: If you want to be able to take the harness off quickly, use this method. Just slip the harness over his head and secure it in place with the Velcro straps.

3. Use the buckling method: If you want to be able to adjust the fit of the harness, use this method. First, buckle the straps around his chest, then adjust them as needed so they are comfortable but still snug.

What type of harness should you buy?

There are a few different types of harnesses that you can use with a pug. The most common type is the pinch collar harness, which is designed to keep the dog close to you. You can also buy a harness with a leash attachment, which will allow you to take the dog out for walks. If you plan on using your pug in activities such as agility or weightlifting, you’ll need to buy a harness with heavy-duty construction.


Putting a harness on a pug can be tricky, but with a little bit of practice, you’ll be able to do it like a pro. Follow these tips to make the process as easy as possible:

-Start by securing the leash around the dog’s neck. Make sure that the buckle is facing down so that it’s easier for them to put their head through.

-Next, take the front part of the harness and fit it over their chest and shoulders. Fit it snugly but not so tight that they can’t breathe. You may need to adjust it once or twice during use to ensure an optimal fit.

-Take the back part of the harness and position it over their stomach just below their ribcage. Make sure that both ends are long enough so that you have enough slack when pulling them along. Finally, connect both pieces together by fitting one end into one hole on each side of the front piece and then threading it through another hole on each side (this will create two loops).


Please enter your comment!
Please enter your name here